Brief Description:Plastic sheet lithium battery host, a new type of thermosetting molding plastic, is used in transportation, construction, and electrical applications. The BMSJ sheet machine is a production equipment for unsaturated polyester fiberglass reinforced composite materials, which involves adding thickeners, fillers, release agents, and curing agents to polyester resin, impregnating fiberglass yarn, and covering both sides with film to form a sandwich structure.
Plastic sheet lithium battery powered main unitIntroduction:
It consists of several parts including the drive unit, feeding device, barrel, and screws. The functions of each component are similar to those of a single-screw extruder, as shown in Figure 1. The difference from a single-screw extruder is that a twin-screw extruder has two parallel screws placed in a barrel with an "∞" shaped cross-section.
Plastic sheet lithium battery powered main unitPrecautions
The temperatures of each section on the plastic sheet production equipment barrel gradually increase from the feeding section to the point where the barrel connects with the forming mold.
2, The mold temperature is slightly higher than the barrel temperature, with the difference controlled at 5-10°C. The temperatures at both ends of the mold are slightly higher than the middle, with the difference also controlled at 5-10°C.
3. For the sheet entry, the upper surface of the middle roller among the three rollers should be at the same level as the lower plane of the die lip; the end face of the die lip should be parallel to the centerline of the middle roller, with a distance of 50~100mm.
4. The die lip gap should be slightly less than or equal to the thickness of the sheet product, with the center gap of the die lip being slightly smaller than the gaps at both ends.
5. Note that the surface roughness R of the three rolls should not exceed 0.2 μm. When cleaning the roll surface, do not use a hard steel blade to scrape it; instead, use a copper knife to remove any residue.
6. The roller surface should have some crown; the gap between the three rollers should be equal to or slightly greater than the thickness of the plate.
7. The temperature control of the molding die must be stable. When the temperature is high, the flow rate of the molten material inside the mold increases; when the temperature is low, the flow rate of the molten material inside the mold decreases. Unstable flow rates of the molten material can cause large longitudinal thickness variations in the plate (sheet) products.
8. Pay attention to controlling the working surface temperature of the three rollers, with the entry roller being slightly warmer and the exit roller slightly cooler. If the roller surface temperature is too high, the sheet will not easily detach from the roller, and horizontal lines may appear on the product's surface; if the temperature is too low, the product's surface will lack luster. Based on these phenomena, the roller surface temperature should be adjusted in a timely manner.
9. The operating speed of the three rolls should be slightly higher than the extrusion speed of the sheet from the die, with a general speed difference not exceeding 10%. The working speed of the three rolls must be controlled steadily, as too fast or too slow operation can significantly affect the thickness tolerance of the sheet.
Maintenance:
All lubrication points should be injected with clean lubricating oil at regular intervals and in the prescribed quantities.
2. Equipment maintenance: Regular cleaning, adequate lubrication, proper use, and reasonable maintenance are essential for maintaining the long-term stability of the equipment.
3. At the end of each shift, the dust, oil, water, and adhered material on the surface of the equipment should be wiped clean (e.g., chains, yarn cutting knives, pressure rollers, upper and lower hoppers).
4. Regularly check the working condition of each air line, maintain unobstructed and stable air pressure (adjusted within the set pressure range), and promptly address any leaks or pressure drops.
5. Electrical equipment should be inspected regularly, paying attention to the operational reliability of all interlock and safety devices, checking for any loose connections at the wiring terminals. Before inspecting the electrical equipment, the main power supply to the equipment should be turned off. The grounding of the electrical equipment must be in good condition. Motors should always be kept clean and dry, and dust should be removed periodically.
Nanjing Xintuo Intelligent Equipment Co., Ltd. was established on May 29, 2020, with Zhou Xianting as the legal representative. The registered capital is 10 million RMB, and the unified social credit code is 91320113MA21LF2H92. The company is located in the Baima Town Industrial Concentration Zone, Lishui District, Nanjing City. It belongs to the other manufacturing industry. Its business scope includes: Permitted projects: import and export of goods; import and export of technology (projects that require approval by relevant departments can only be carried out after obtaining such approval, specific business items are subject to the approval results). General projects: sales of intelligent material handling equipment; research and development of machinery and equipment; general equipment manufacturing (excluding special equipment manufacturing); specialized equipment manufacturing (excluding licensed specialized equipment manufacturing); sales of metal products; wholesale of electronic components; sales of instruments and meters; sales of artificial intelligence hardware; processing and sales of mechanical parts and components; general component manufacturing; sales of plastic products; production and sales of Class I medical devices; sales of Class II medical devices; sales of health supplies and disposable medical supplies; sales of special labor protective equipment; technical services, technical development, technical consultation, technical exchange, technology transfer, and technology promotion (except for projects that require approval, activities can be conducted independently according to the business license). The current operating status of Nanjing Xintuo Intelligent Equipment Co., Ltd. is active (in operation, open, registered).
