Brief Description:Material modification extrusion and pelletizing equipment is mainly used for coloring polymer materials, primarily divided into black masterbatch, white masterbatch, color masterbatch, and liquid color masterbatch.
Material modification extrusion and pelletizing equipmentIntroduction:
The internal structure of the machine largely depends on the design principles, and it can be said that technical elements influence its internal structure. The internal structure, in turn, serves as the basis for the external form, or in other words, the external form is the outward manifestation of the internal structure. This relationship is particularly evident in the exterior design of box-type components.
In addition to the internal structure, there is an inclusive relationship between the internal structure and the external form, with the external form sometimes being a structural design in itself. Given that the main work of industrial design is reflected in the appearance of the equipment, the structural and form design of the exterior components are very closely related.
In the degradable material modification pelletizer, the change in screw speed is achieved by adjusting the motor speed. The drive motor typically rotates at full speed of about 1750 rpm, which is too fast for an extruder screw. If it were to rotate at such a high speed, it would generate too much frictional heat and result in insufficient plastic residence time, making it impossible to prepare a uniform, well-mixed melt. The typical reduction ratio should be between 10:1 and 20:1, with the first stage using either gears or pulleys, but the second stage uses gears and positions the screw at the center of the large gear. For some slow-running machines, there may be three stages of reduction, with the final speed possibly as low as 30 rpm or lower (a ratio of up to 60:1). On the other hand, some long twin-screws used for mixing can operate at speeds of 600 rpm or faster, thus requiring a very low reduction ratio and more intense cooling.
Material modification extrusion and pelletizing equipmentPrecautions
Incorporation of iron impurities
First, during the use of this equipment, we must inspect the material being fed in. The material should not contain any iron impurities, as these can cause damage to the machinery or excessive wear.
2. Idle Adhesive Shaft
Secondly, during use, we must also prevent the machinery from running idle without any load, as idling can cause the shaft to heat up, leading to clumping and adhesion of various materials. Throughout the process, we need to inspect and select the materials being fed in, constantly monitoring whether the machinery is in an idle state, and promptly removing any impurities mixed within the materials. This way, we can extend the service life of the machinery.
After the temperature stabilizes, the machine can be started. Before starting, the bolts of the die head and the extruder flange should be tightened again to eliminate the difference in thermal expansion between the bolts and the die head. The sequence for tightening the die head bolts should be diagonally, with even force applied. When tightening the die head flange nuts, ensure they are uniformly tight around; otherwise, material leakage may occur. To start, select the preparation start button, then press the start button, and slowly adjust the screw speed using the speed control button, gradually increasing the screw speed. Then, gradually accelerate while feeding a small amount of material. During feeding, closely monitor the changes in the main motor's current meter and other indicator gauges, ensuring that the screw torque does not exceed the red mark. No one should stand in front of the die before the plastic profile is extruded, to avoid injury due to bolt breakage or unexpected moisture release. After the plastic is extruded from the die, it needs to be slowly cooled, and the equipment and sizing dies should be moved, then adjusted according to the readings on the control instruments.
Nanjing Xintuo Intelligent Equipment Co., Ltd. was established on May 29, 2020, with Zhou Xianting as the legal representative. The registered capital is 10 million RMB, and the unified social credit code is 91320113MA21LF2H92. The company is located in the Baima Town Industrial Concentration Zone, Lishui District, Nanjing City. It belongs to the other manufacturing industry. Its business scope includes: Permitted projects: import and export of goods; import and export of technology (projects that require approval by relevant departments can only be carried out after obtaining such approval, specific business items are subject to the approval results). General projects: sales of intelligent material handling equipment; research and development of machinery and equipment; general equipment manufacturing (excluding special equipment manufacturing); specialized equipment manufacturing (excluding licensed specialized equipment manufacturing); sales of metal products; wholesale of electronic components; sales of instruments and meters; sales of artificial intelligence hardware; processing and sales of mechanical parts and components; general component manufacturing; sales of plastic products; production and sales of Class I medical devices; sales of Class II medical devices; sales of health supplies and disposable medical supplies; sales of special labor protective equipment; technical services, technical development, technical consultation, technical exchange, technology transfer, and technology promotion (except for projects that require approval, activities can be conducted independently according to the business license). The current operating status of Nanjing Xintuo Intelligent Equipment Co., Ltd. is active (in operation, open, registered).
